Crestron 1:4 HDMI Distribution Amplifier w/4K60 4:4:4 & HDR Support

Key Features

• Splits one HDMI® source to four outputs
• Handles 4K60 4:4:4 and HDR video signals
• Fully compatible with HD 1080p, UHD 4K, and DCI 4K sources and displays
• Handles 3D video and Deep Color
• Handles Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X®, and uncompressed 7.1 linear PCM audio
• Selectable handling of HDCP 2.2 or HDCP 1.4
• EDID management options
• Input and output video presence indication
• No programming or control system required
• Thin profile – less than one inch deep
• Surface, shelf, or single rack rail mountable
• External 100-240V universal power pack included

Technical Specifications

• Video
  • Input Signal: Type HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support (DVI & Dual-Mode DisplayPort compatible)
  • Output Signal Type: HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support (DVI compatible)
  • Copy Protection: Selectable for HDCP 2.2, HDCP 1.4, or HDCP disabled
  • Maximum Resolutions

    • Scan Type	Resolution	Frame Rate	Color Sampling	Color Depth
      Progressive	4096x2160 DCI 4K or 3840x2160 4K UHD	24 Hz	4:4:4	36 bit
      		30 Hz	4:4:4	36 bit
      		60 Hz	4:2:2	36 bit
      		60 Hz	4:4:4	24 bit
      	2560x1600 WQXGA	60 Hz	4:4:4	36 bit
      	1920x1080 HD 1080p	60 Hz	4:4:4	36 bit
      Interlaced	1920x1080 HD 1080i	30 Hz	4:4:4	36 bit

• Audio
  • Input Signal Type: HDMI (Dual-Mode DisplayPort compatible[2])
  • Output Signal Type: HDMI
  • Formats: Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS-ES, DTS 96/24, DTS HD High Res, DTS HD Master Audio, DTS:X, LPCM up to 8 channels
• Communications
  • USB: USB 2.0 host; supports firmware update and custom EDID upload via a USB flash drive
  • HDMI: HDCP & EDID (does not pass CEC)
  • HDCP Version:
    • Selectable for HDCP 2.2, 1.4, or OFF;
    • HDCP encrypted content is blanked in OFF mode
  • EDID Mode:
    • Selectable for DEFAULT or COPY 1ST;
      
      • The factory default EDID is 4K60 4:4:4 non-HDR video with 2-channel LPCM audio;
      • The factory default EDID can be replaced with a custom EDID via USB;
      • Sliding the switch from DEFAULT to COPY 1ST copies and stores the EDID from the device at OUTPUT 1 and passes it to the INPUT source device;
      • Sliding the switch from COPY 1ST to DEFAULT erases the stored EDID and uses the factory default or custom EDID;
      • Note: Changing the device at OUTPUT 1 will not update the stored EDID until the switch is moved to DEFAULT and back to COPY 1ST
• Connectors
  • INPUT:
    • (1) HDMI Type A connector, female;
    • HDMI digital video/audio input;
    • (DVI & Dual-Mode DisplayPort compatible)
  • OUTPUT 1 – 4:
    • (4) HDMI Type A connectors, female;
    • HDMI digital video/audio outputs;
    • (DVI compatible)
  • SERVICE:
    • (1) USB Type A connector, female;
    • USB 2.0 host port;
    • For firmware update and custom EDID upload via a USB flash drive
  • 24VDC 0.75A:
    • (1) 2.1 x 5.5 mm DC power connector;
    • 24 Volt DC power input;
    • PW-2407WU power pack included
• Controls & Indicators
  • PWR: (1) Bi-color LED, indicates operating power is supplied via the power pack; illuminates amber while booting, green when operating
  • SETUP: (1) Pushbutton and (1) red LED, restores factory settings
  • RESET: (1) Recessed pushbutton for hardware reset
  • INPUT: (1) Green LED, indicates video signal presence at the HDMI input
  • OUTPUT: 1 – 4 (4) Green LEDs, each indicates video signal transmission at the corresponding HDMI output
  • HDCP: (1) 3-position slide switch, selects the HDCP version (OFF, 1.4, or 2.2)
  • EDID: (1) 2-position slide switch, selects the EDID mode (DEFAUT or COPY 1ST)
• Power
  
  • Power Pack (included)
    • Input: 100-240 Volts AC, 50/60 Hz;
    • Output: 0.75 Amps @ 24 Volts DC;
    • Model: PW-2407WU
  • Power Consumption: 5.5 W (typical)
• Environmental
  
  • Temperature: 32° to 104° F (0° to 40° C)
  • Humidity: 10% to 90% RH (non-condensing)
• Enclosure
  
  • Chassis: Metal, black finish, with (2) integral mounting flanges
  • Mounting: Freestanding, surface mount, or attach to a single rack rail
• Dimensions
  
  • Height 0.87 in (22 mm)
  • Width 8.09 in (206 mm)
  • Depth 4.67 in (119 mm)